Garage Door Repair Vancouver BC
Repair BC
24/7 Emergency Services
  1. Garage Door Repair BC
  2. Blog
  3. Garage Door Cable
17Apr 2020

How To Replace A Garage Door Lift Cable

Garage doors are used daily, and as we all know, wear and tear are always in effect. At some point, your garage door is going to break down in its use. It is, therefore, important that you be prepared for any situations that may occur. One of those situations is when the garage door lift cable breaks. You will need to know how to replace it. Follow these steps in order to replace garage door lift cable in Coquitlam. To do this, you also have to replace the springs.

Garage Door Lift Cable Replacement

You have to be cautious all the way to avoid hurting yourself. If you can’t, then get a professional to do it for you.

The following are the things you need to get the work done:

  1. Clamps
  2. Adjustable wrench
  3. Wrench set
  4. Winding bars
  5. Socket
  6. Safety glasses
  7. Rags
  8. Locking pliers
  9. Hammer
  10. Cordless drill
  11. Leather gloves
  12. Lift cables
  13. Bottom brackets
  14. Torsion springs

Steps

  1. Lock the door down and clamp it to the track. This helps in preventing the door from shooting up, which may result in you breaking your nose.
  2. With the winding bar, loosen the spring that is not broken.
  3. With the two winding bars, loosen the spring that is not broken.
  4. Remove the bolts and nuts then disconnect the spring at the center of the brackets.
  5. With the locking pliers, lock the torsion tube in position.
  6. Remove the old springs and slide the torsion tube over. Make sure to start on the left side and carefully slide the torsion tube to the right for you to be able to remove the eardrum of the cable and slide off the old spring from the tube.
  7. Take all the necessary measurements and determine the parts you need to buy. The measurements include the diameter of the wire and the broken spring.
  8. On the left side, install the new spring, after assembly, hang the bearing on the bracket.
  9. The new center bearing, install it, and then to the bracket, you connect the stationary cones.
  10. This is where the cable, which is the main topic, comes in. In this step, you have to replace all the brackets at the bottom, the lift cable, and the rollers.
  11. Run the cable of the lift straight up between the doorjamb and rollers.
  12. Make the drums tight; make sure to lock the torsion tube in place using the pliers to avoid accidents. The torsion on both sides has to be equal if the door is to open evenly.
  13. With the recommendations of the spring’s supplier, wind them.
  14. Lengthen the springs by stretching them.
  15. The very final step is the lubrication of the spring.

Taking a look at all the procedures involved, it may take hours for you to complete this task. It will be cheaper, safer, and less time consuming if you hire a professional to do it for you.

8Apr 2020

How to Install a Garage Door Safety Cable

Garage doors are home components that are always in operation and, therefore, constantly exposed to wear and tear. They are a safety feature of the garage door running through the torsion springs and does the heavy lifting of the door every time it comes up or goes down. The cable also works as a backup just in case the spring fails. This way, it prevents violent spring recoil and prevents any damage or injury to the door or any property. The cables can sometimes slacken and come out of the track, or if the tension is too high, they can snap and fall off.

Garage Door Safety Cable

Worn out cables must, therefore, be replaced as a form of maintenance activity. However, installing garage door cables is not a difficult task. If you are that person who is comfortable with wires and cables, your basic experience is enough to assist in the installation of new cables without involving an expensive garage door technician. Those processes must, however, be procedural and follow certain prescribed processes. Before attempting cable repair, find out the cause and kind of damage and follow the following steps.

Step 1 – Avail the required tools and materials

Installing the cables and adjusting the door springs certainly require certain tools and materials. You need to gather all the required tools prior to beginning the process in order to avoid running up and down once you begin the process.

Step 2 – Wrap the cables

Having provided all, you need to begin the process. Take the pulley-guide and wrap the cables on them. Make sure the cables are extending on either side to allow for easy connection with the ceiling as well as the track. Always close the garage door before routing the cables. This way, you will be able to tighten them adequately using your screws.

Step 3 – Attach the cables

The door bottom has slots for attaching the cables. Attach the cables in the slots making sure that the cables rest comfortably on the track of the door. Remember that if the cables do not rest on the track properly, then the whole installation process will flop. Once this is confirmed, attach the other ends on the overhead setting. This is done by unscrewing or losing the screws before fixing the cables in it. Once this is done, use a screwdriver to tighten the screws back and make sure the cables attain the necessary tension to reduce wear when the door is in operation.

Step 4 – Installation troubleshooting

Once the cables are installed, you should attempt to operate the door by opening and closing carefully to check if the door operates normally. You should begin by confirming that the cables are resting properly on the track, as mentioned earlier. Also, check that the cables are not too short and have the most appropriate tension. It is advisable to have a longer cable as this can be easily repaired in case of an issue. It is vital to keep the cables free from the accumulation of debris by avoiding the use of heavy lubricants, which may attract dirt.

30Mar 2020

How to Maintain Garage Door Cables

Garage door cables are a key garage door feature that must be carefully maintained and protected from regular repair. A few tips on how you can be maintained are provided by this article.

Garage Door Cables Repair

Tighten the hardware

A garage door is constantly on the move as it opens up and closes every day. This exposes the garage door cables to constant pressure and tension. The hardware of the door also loosens up and exerts additional pressure on the door and door cables. Tightening up these parts makes the door more stable and protects the cables much better.

Look and listen

Take your time whenever you use the garage door to observe carefully and listen to the door as it moves up and down. This way, you are able to listen to strange noises and even notice irregularities in the door motion. Does it operate silently? Are both sides of the cables symmetrical? Any irregularities noticed should be handled with care, and a professional technician should always be involved to repair or replace the garage door cables.

Test the balance

Ensuring that the garage door is properly balanced is one key step towards ensuring that the door cables will work optimally, and the door itself will operate more efficiently. The strain caused by the imbalance on springs and cables makes the general operation of the door less effective. If this happens, it should be left to a professional to rectify as attempting a self-repair may be dangerous.

Lubricate moving parts

Coat the overhead sprigs with lithium grease regularly to increase the lifetime of your garage door. This also helps to keep the garage door cables and other door integrals in good condition as there is no damage caused as a result of the poor operation from other door parts.

Constantly check the cables

Always check for broken strands and damages, especially near the bottom roller bracket. These damages will always occur as the door is in operation as may also be caused by neighboring parts, as already discussed in step five. However, self-repairs should never be tried as these cables are high tension and are very dangerous to handle without prior skills. In case of damages, a professional technician should be brought on board to assist with repairs or replacement.

Clear the tracks

Always check to ensure there are no foreign objects on the tracks. Debris and other objects will knock the garage door and expose it together with other components such as cables to damages. They may also warp or get misaligned, causing stress on the door cables. This way, you will identify and correct possible problems that may end up ruining your door cables and the general functionality of the garage door.

Groom the door

Always remember that your garage door is a very important home feature and makes up to one-third of the exterior of your house. Keep it fresh and clean! If you do not have time to do this regularly, call a garage door professional to schedule a fine-tuned service. This way, you’ll keep your garage door cables under check and thus keep them working effectively for longer.

MENU